Browse Products

MM-1189 Thix-Sil™ Thixotropic Agent - Thickener For Platinum & Tin Silicone is a liquid chemical thickener that is made especially for thickening silicone rubbers.  It's specially designed to be used with TraumaSkin FX™ Platinum Silicone Sculpting/Casting Medium, MM-1002, to create a higher viscosity (more dense) mixture for direct to skin freehand molding and sculpting application that produces realistic skin casualty simulation results.  Using Thix-Sil™ is very important to add if you are going to cast an extra soft Shore A (10-30) Hardness silicone product, such as TraumaSkin FX™ Platinum Silicone Sculpting/Casting Medium, into a rigid mold.  This will result in a smooth pull, and producing realistic skin-like prosthetic appliances that are firm and sturdy enough for library (repeated use) pieces. 

See details for more information about using this product.

Smooth-On XTEND-IT® is an aerosol delivered dry gas blanket designed to extend the shelf life of sensitive polyurethane, plastic and foam products in their liquid state, especially if stored in large amounts or containers.  It works by completely displacing the air (and any atmospheric moisture) from the container it is sprayed into.  This protective blanket is a must if you have very large containers of these products that are opened frequently or stored for long periods of time.  Helps to prevent material degradation due to air exposure.

See details for important information.

This product is flammable and considered hazardous material (HAZMAT).  Due to HAZMAT regulations, this product is ground shipping only within the continental USA and cannot be shipped overseas. 

Body Double® Release Cream is a non-toxic skin conditioner that will aid in releasing Body Double® mold rubber from skin surfaces with or without hair.  It is highly concentrated, so a little goes a long way.

Body hair not thoroughly coated with a release cream will become encapsulated and stuck in silicone rubbers during the cure phase.  When that happens it can be difficult & painful to separate hair from the silicone.  Release Cream can also be used in conjunction with other release additives such as Smooth-On HYPER-FOLIC®.

See details for more important information on this product.

RCMA Dulling Powder is a mattifying agent made from a fine silica mixture that has a very high matting efficiency with very high transparency.  It provides a completely dull matte finish on any shiny textured prosthetic appliances, especially silicone based appliances and prosthetic transfers.  The colorless powder can also be used on heavier textured makeup applications, such as theatrical grease paints, adhesive based paints such as PAX, etc. to eliminate surface shine and tackiness.  SFX and Beauty artists alike have used this great dulling powder for decades for a variety needs that calls for a stronger transparent powder to permanently matte down and eliminate surface shine and tack before moving to the next step in a makeup application.  It's a great substitute alternative for Cab-O-Sil, because it doesn't contain crystalline/amphorous silica, so it can be used on makeup covered skin and prosthetic appliances.  It's also the perfect matting agent for use in sealers and adhesives as it dissolves completely and won't add any extra thickness or density in the end result.  Avoid using near the eyes, nose and mouth.

See details for more information.

MM-1469 Smooth-On Thi-Vex® Silicone Thickener is a thixotrophic additive liquid (thickening) agent that can be blended into many types of liquid silicone rubber products for two main reasons: to facilitate a thicker vertical surface application with brush-on methods, or to create a more dense-firmer freehand sculpt or hard surface molded appliance.  It is designed to thicken the catalyzing silicone mixture when added as a small percentage of Part A.  It then must be thoroughly mixed in together with Parts A and B of the silicone compound before pouring or brushing.  Different viscosities (thicknesses) can be attained in the end product by varying the amount of Thi-Vex® added to the mixture. 

See details for more information about using this product properly.

MM-1527 Smooth-On Silicone Thinner® is a non-reactive silicone thinning fluid that will lower the mixed viscosity of either tin cure or platinum cure silicone rubber products.  This product provides a lower mixed viscosity of the A+B parts mixture, and also de-air faster when vacuum degassing the mixture.  The mixed rubber will also flow better, even over the most intricate details of your  mold model's features.  Silicone Thinner® will also lower the ultimate shore hardness (durometer) of the cured silicone rubber piece.  The pot life is also increased in proportion to the amount of Silicone Thinner® used.  The ultimate tear and tensile strength are also reduced in proportion, however knotty tear properties of the Mold Max rubber series are unaffected. 

See details for more information.